After you receive the software, we will send all instructions needed to install and provide the after-sale support. Your Rating:. How to order? Skype: epc. All items on the inspection form Fig. The purpose of the 30—hour inspection is: 1. For adjustment and inspection after first work period 2. To correct wrong maintenance and operation methods. For demonstration of correct service procedures to customer. All items on the 30—hour inspection form Fig.
When the 30 hour inspection has been completed, the form must be signed by 1 the mechanic that completed the inspection, 2 the dealer, and 3 the owner or operator. Failure to do so will result in damage to the machine or its engine. The service schedule must be used as a guide to correct maintenance of the Bobcat loader. Use this schedule unless it is to shorten the intervals due to extremely hot, cold, dusty or corrosive operation conditions.
Inspect condition of system. Check and add oil as necessary. Check coolant lever. Add coolant when low. Remove any debris from radiator grill area. Check rear door grill and blower inlets for restriction of air flow. Clean cylinder cooling fins and blower housing, when necessary.
Inspect for damage and check air pressure in tires. Add lubricant to all fittings Check for correct operation of all inficatos, switches, lights. Check condition of guard and bolts. Check condition of straps and buckle and make replacement if there is a defect. Be sure all decals are in place and can be read. Make replacement as necessary. Check level and add recommended fluid if necessary. Make replacement of oil and filter.
Clean breather cap every oil change. Check water level. Add water if necessary. Check operation. Make repairs and adjustments as necessary. Inspect locking levers and wedges for condition and operation. Make adjustment as necessary. Put 3 — 5 frops of oil in spring cap oil cup. Remove plug. Run engine to remove carbon.
Check level. Add fluid if necessary. Make replace of filter element. Tighten to correct torque after first hours. Also make adjustment to valves if necessary. Inspect system for leaks. Replace element, if necessary. Push down on the door stop to hold rear door open while servicing the engine. Be sure to disengage the door stop before closing the rear door Fig. Use oil of correct SAE viscosity for temperature conditions at the time of starting See Page 1—6 ; not for the highest temperature expected during the working day.
Checking Oil: Engine must be stopped to check oil level. Check oil level every 4 hours for the first 50 hours of operation. After the first 50 hours of operation, check oil level every day, 8—10 hours.
Oil Filter. Install drain plug. Clean area around filter base. Put clean oil on gasket of new filter and install new filter. Tighten filter by hand only. Fill with 4 quarts 3, Clean the breather assembly every hours. Clean the breather cap in solvent every time you replace the engine oil.
The air cleaner system must be kept clean and free from defects for good engine performance and long service life. Service air cleaner as follows: 1. Remove and clean dust cup every day Fig. Do not remove element unless replacement is necessary. NOTE: Be sure 1 gasket surfaces are clean before installing new element and 2 be sure gasket is in correct place.
Inspect complete air cleaner system and make replacement of any parts with defects. Be sure hose connections are tight. Check running operation of air cleaner system as follows: a. Start engine and run at idle. Close air inlet on air cleaner. The engine speed must become slower then stop , only. Check the condition indicator for the red ring ; if the red ring appears, the system is good.
NOTE: Use special care when installing and tightening the hose clamp on the carburetor on the Bobcat engine. Because of the short clamp area on the air inlet of the carburetor the clamp and the hose must be pushed toward the carburetor when the clamp is being tightened Fig.
Engine must be stopped, ignition off, and the engine cool before putting fuel in tank. Remove fuel cap Fig. Put fuel in the tank ONLY when the machine is in a large open area outside or a large building. Stop and cool the engine before adding fuel. Failure to obey warnings can cause an explosion or fire.
Fuel Filter A fuel filter is located on the right side of the loader near the fuel tank outlet Fig. Install the parts as shown in figure 1—21 See Parts catalog for the Parts. The fuel filter must be replaced every hours.
To check or make replacement of fuel filter. Turn fuel valve off Fig. Loosen hose clamp and remove hose from outlet end of fuel filter. Connect a short piece of hose to the outlet end of fuel filter and turn fuel valve on. If fuel hose goes through the filter, it does not need replacement. If fuel does not go through filter, make replacement. When installing new fuel filter, loosen both hose clamps to remove filter. Install fuel filter with arrow towards carburetor Fig. Fuel Pump The fuel pump is located on top of the cylinder block and under the intake manifold.
Repair parts are not available for the fuel pump. If the fuel pump does not operate correctly, replacement must be made. NOTE: Too much fuel to the engine can be caused by the pump pressure being too high.
Run engine at full RPM. Correct pressure is 2—3 PSI 13,79—20,68 kPa. Also, too a low pressure will cause vapor lock. If the fuel pump does not operate correctly, replace the pump. Carburetor The carburetor is located at the center of the engine on the intake manifold. Repair kits are available for the carburetor.
Idle Adjusting Needle 1. Turn needle all the way in. DO NOT use force, it will cause damage to the needle. Start the engine. Hold governor speed change lever against the stop. All the same year, the A was introduced in Europe, a loader that combines skid steer and all-wheel steering, which is achieved in the operator's cab with a simple flick of a switch. There have been no analogues of such a model in the world yet.
In Bobcat starts production of mini excavators. Further expansion of products was dictated by the latest technologies, innovative developments and investments. A new training center and plant has opened in the Czech Republic, which produces new models of telehandlers.
In , the Bobcat company celebrated its 50th anniversary. The interim results and analysis of how the Bobcat brand was created were summarized. In the middle of the last century, the main emerging markets were fertilizer producers and dairy farms. Bobcat experts came up with a simple scheme - to paint the cars in white paint as a symbol of cleanliness and sterility.
This color, new logo and company name have become the trademark of Bobcat, a mark of success and quality. Bobcat today is the largest manufacturer of construction and agricultural equipment with more than dealers in more than 75 countries around the world. The main products of the company are compact excavators, attachments and skid steer loaders. All in the same Europe, the name "Bobcat" began to be applied to any loader, regardless of the manufacturer, with which the American company has been struggling for several years.
For over 50 years, much has changed, but one thing has not changed - Bobcat's commitment to professional excellence and excellence through innovation and pioneering spirit. Pam Monday, 20 December Looking for a working link to a bobcat g service manual. Can you help me. Tractor Free Service Manuals.
0コメント